P2 · Information / Sourcing guide
Buying Camellia Oil in Bulk: Eight Questions Worth Asking
Most camellia oil enquiries fail on the same eight points: nobody asks how it was extracted, what the tested values actually are, or who refines it. This page lists the questions a buyer should ask any supplier, including us, and answers each one with a number you can check.
- 01
Is it cold pressed, or solvent extracted?
Ask for the pressing temperature, not the word "cold pressed". Ours is held at or below 60 °C in twin-screw presses, and no solvent is used at any stage. Solvent residue was not detected, at a limit of detection of 2 mg/kg. If a supplier cannot state a temperature, the phrase means nothing.
The pressing line, temperature control and solvent question are covered in full on our cold pressed camellia oil page.
- 02
Is it one grade, or blended from batches?
Two questions in one. Grade: ours is either cold pressed and unrefined, or fully refined — both split from the same batch of seed, neither blended with anything else. Batch: one batch code follows the oil from seed intake to drum, and it is printed on the certificate.
Grade and batch terminology is explained in our camellia oil guide.
- 03
What are the tested values, as opposed to the specification?
A specification is a promise; a test report is a fact. The figures are for the cold pressed, unrefined grade: oleic acid 80.0 %, acid value 0.94 mg KOH/g, peroxide value 0.013 g/100 g, smoke point 215 °C. Report No. A2240440191101001C from Centre Testing International, verifiable at mycti.cti-cert.com with code SEF9.
Every value above, with its limit, is listed on the full specification page, and how the testing is commissioned and verified is described under our quality control process.
- 04
What is the limit of detection on the contaminants?
"Not detected" is meaningless without a number. These detection limits are from the cold pressed grade report: 0.02 mg/kg for lead, 0.003 mg/kg for total arsenic, 0.03 µg/kg for aflatoxin B₁, 0.2 µg/kg for benzo[a]pyrene — none found. That is 33, 333 and 50 times below the limits we test to. A supplier who will not state a detection limit is telling you the number is not favourable.
The full table of contaminant detection limits is on the specifications page.
- 05
Does the price match the extraction method?
Cold pressing returns less oil per tonne of seed than solvent extraction, so genuine cold pressed oil costs more to make. That yield gap, not positioning, is what the price difference reflects. If a quote sits close to refined oil pricing, ask what is actually in the drum.
The yield and cost logic behind why cold pressing costs more is set out on the cold pressed page.
- 06
What is the minimum order, and will it fit a first run?
Bulk oil starts at 5 MT — about a quarter of a 20-foot container, so a first order does not have to fill one. Samples are free; you cover the freight and it is credited against your first order. Private label also starts at 5 MT. One floor for both, confirmed in the quotation.
Packing and MOQ details are on the supply capability page, and private label options are described on the private label page.
- 07
Who presses it, and who refines it?
The same company, on the same site. We press the seed at our plant in Qiyang, Hunan, then split the stream: part ships as cold pressed and unrefined, part goes through four-step refining on the same premises. There is no third party in between, which is why one batch code can cover both grades.
The line itself is described under pressing and refining equipment, and more about the company is on the about page.
- 08
What happens if a batch fails your specification?
It is returned and re-tested. It is not blended into a passing batch to recover the volume. That is a policy rather than a marketing line: if you audit our plant, ask to see the non-conformance records.
Our batch handling policy is part of the quality control page.
If you have an eight-question list of your own, send it. We answer in writing, with numbers, before any pricing discussion.